Fast delivery
Sea&Air
MO-1 Metallographic specimen mounting press
MIC-MO-1 Metallographic specimen mounting press is suitable for the thermo-hardening plastic pressing of the small metallographic specimen which is not idiomorphic or hard to take. After forming, it will be very easy to process the grinding, polishing of the specimen and it is also convenient to process measuring of metallographic structure under metallographic microscope. The machine may work stable under the following working condition:
The temperature of surrounding medium can not be less than 10 °C and more than 40 °C
The relative humidity of air should be no more than 85% (20 °C)
The voltage fluctuation should be no more than 15%
There should be no obvious vibration source around
There should be no current conducting dust, explosive and corrosive air.
MO-5 Metallographic specimen mounting press
MIC-MO-5 automatic metallographic specimen mounting press is a kind of full automatic mounting press, equipped with in-out water cooling system. It is suitable for the heat mounting (thermo hardening & thermoplastic) for all kinds of materials. After the parameters such as heating temperature, heat preserving time and applied force etc. are set up, put the specimen and mounting material into the machine, close the cover and press the start button, then the machine will finish the job automatically. It is not necessary for the operator to be on duty. According to different requirements of the material, there are four kinds of moulds that can be chosen to meet the demands at will. Also it is available to prepare two pieces of specimens at the same time, the capacity is doubled.
MO-6 Metallographic specimen mounting press
MIC-MO-6 is a new Touch screen type Automatic Metallographic specimen mounting press, all working procedures can be done automatically. After the parameters such as heating temperature, heat preserving time and applied force etc. are set up, put the specimen and mounting material into the machine, close the cover and press the start button, then the machine will finish the job automatically. It is not necessary for the operator to be on duty. According to different requirements of the material, there are four kinds of moulds that can be chosen to meet the demands at will. Also it is available to prepare two pieces of specimens at the same time, the capacity is doubled.
SXQ-2 Metallographic Sample Mounting Press
SXQ-2 Metallographic Sample Mounting Press
Introduction:
Mounting is a very important process of metallographic sample preparation, especially for some difficult holding tiny samples, irregularly shaped samples, and what needs for protecting edge or automatic grinding and polishing, mounting is an essential procedure before sample preparation.
SXQ-2 metallographic sample mounting press is improved on the basis of the classic model XQ-1. With long mould and high heating power, it has high efficiency. The mould cover adopts the rotating thread structure, which is convenient and safe to open the cover. The integrated control interface has real-time display of total mounting time and temperature and visualization of mounting state, which makes the operation more humane. With water cooling system, it makes sample preparation fast. It has stable and reliable performance and easy operation, which is the economic choice for sample mounting. (Only for thermosetting materials, such as Bakelite powder, Urea formaldehyde molding powder etc.)
VIM-1 Vacuum Mounting Press
VIM-1 Vacuum Mounting Press
The machine consists of a vacuum chamber, an indexing assembly, a fuselage assembly, a feed assembly, and a vacuum pump. This model can realize multi-sample setting, which can be quickly converted between each station to improve work efficiency.
VXQ-1 vacuum mosaic machine
Technical data
Operating pressure: 2.0 bar
Safety valve: 2.8 ~ 3.3bar
Connecting pipe: 3 ~ 10bar
Vessel size: maximum outer diameter: 277mm, total height: 300mm
WXQ-2B Automatic Mounting Press Machine
WXQ-2B Automatic Mounting Press Machine
Application
This machine is designed for purpose of the last process before polishing. It is setting up those small, difficult-to-hold or irregular specimens for metallographical test. It can facilitate polishing and watch properly the ideal material structure and measure the hardness of the material by hardness tester. The inserts for this machine are limited to thermosetting materials only .The punching temperature of different thermosetting materials can be adjusted depending upon the features of materials .
XQ-2B METALLOGRAPHIC SPECIMEN MOUNTING PRESS
MODEL XQ-2B METALLOGRAPHIC SPECIMEN MOUNTING PRESS
Model XQ-2B Metallographic specimen mounting press is suitable for the thermo-hardening plastic pressing of the small metallographic specimen which is not idiomorphic or hard to take. After forming, it will be very easy to process the grinding, polishing of the specimen and it is also convenient to process measuring of metallographic structure under metallographic microscope, or hardness testing. This machine adopts digital display temperature controller to control the temperature, and uses timer to control the sample preparing time. After sample preparation is finished, it will cut off power supply automatically. It is the ideal sample preparing equipment to be used in factories, researching institutes and college laboratories.
YZXQ-1 Automatic Metallographic Sample Mounting Press
YZXQ-1 Automatic Metallographic Sample Mounting Press
Automatic Metallographic Sample Mounting Press is used to mosaic small specimens, specimens in irregular shapes, or specimens which are not easy to take up-the preceding process before grinding and polishing metallographic or rock specimens. The mosaic operation serves to facilitate the grinding and polishing operations of the specimens and the routine observation of the composition of the material under the metallographic microscope. The machine is heated, and intensified with pressure automatically. After the formation of the specimen under pressure, it stops the operation and discharges the pressure also in an automatical way. With another press of the knob, the machine automatically turns up the specimen, which may be taken away. Note: It is only for the hot solid materials (such as urea-formaldehyde molding powder and bakelite powder) with the temperature automatically regulated and controlled.
